This Kia Rio had a severe engine vibration, see the picture below for the cause.

There are several things that can cause an engine to shake. If there is an engine vibration problem, typically it gets worse with the air conditioning turned on since there is more of a load on the engine. In this auto repair article, we will cover several things that can be looked at to help diagnose the problem. Misfires can definitely cause an engine to shake, usually in most late model cars a misfire will almost always be accompanied by a CEL (Check Engine Light) and misfire code. Many times if the engine also stalls, there could be excess carbon build up on the throttle plates or IAC (idle air control motor). Cleaning the throttle body and IAC is a common practice when trying to eliminate possible causes of engines vibrating.

Read the rest…

Honda Ridgeline is one of the vehicles affected by TSB 08-045

Honda has always been a little different when its comes to their TSB’s (Technical Service Bulletins). They have used terms that are down to earth, that mechanics can understand easily. Plenty of technical information but without all the technical talk. Honda has now gone above and beyond their previous efforts to inform technicians about issues and fixes. The PDF provided by Honda not only has pictures, it has video and sound!

Read the rest…

Chrysler 300 with only 37,000 miles overheated & towed in

What would cause two cooling fan motors to be out at the same time? One possibility is that they didn’t fail at the same time, one failed and the car was still able to be driven until the other failed also. But two fan motors failing on a car that only has 37,000 miles didn’t make sense either. Obviously power and ground supply was first checked with a power probe to verify the motors were getting the correct input to allow them to run. Once the fan motors were replaced, a terrible ticking noise was heard. More pictures below:

Read the rest…

2000 Ford Expedition P0401 doesn’t necessarily mean the EGR is bad

Don’t replace the EGR (Exhaust Gas Recirculation) valve just yet if you have a P0401 code on a 4.6 liter engine like the one in this Expedition. The diagnostic code definition states “Low flow from E.G.R.” Low flow doesn’t mean definitively that the EGR is bad. Low EGR flow can be a problem in any Ford, Mercury, Lincoln, Mazda and many other car’s for that matter. On a lot of Ford vehicles this code will mean there is a faulty Differential or Delta Pressure Feedback (DPFE) sensor. This was such a common problem there was an extended warranty coverage on them for awhile. Not many people knew about Ford covering these on some models for an extended period of time. At the shop I worked at, an extended warranty company first alerted us to this when they declined an extended warranty claim because Ford would replace it under warranty.

Read the rest…

Wiring can cause door lock problems, switches and actuators are more common

There are several things that can cause the power door locks not to work properly. The most common cause of a single door lock not to work, is a bad door lock actuator (also called a door lock solenoid). Another common problem or cause of door locks not working is simply a bad door lock switch. Many cars today have computers that are also in the loop when it comes to controlling the door locks. Fortunately, body computer systems are pretty dependable and give problems seldomly. It seems as though the most troublesome vehicles regarding door locks related to computer control issues, are Chrysler’s; Dodge Caravan and Chrysler Town & Country vans sometimes have BUS related issues (BUS means “a collection of wires through which data is transmitted from one computer to another”)… but this is still rare. Ford Explorers also have a few BUS issues that can be related to door lock security module, or wiring shorting out that goes from the door into the body. Usually when checked with a scan tool in the body control or security section, there will be a code indicating if there’s a BUS fault.

Read the rest…

Leaves accumulated near the fresh air intake can enter the car’s evaporator case.

There are several things that can cause low airflow from a vehicle’s air conditioning system. The strongest blowing vents are the middle ones with the setting adjusted to maximum or recirculate. On the max setting, the air is recirculated in the passenger compartment. Obstructions can include leaves, loose articles from the glove-box, a broken or out of position door in the Heating Ventilating & Air Conditioning (HVAC) case.

Read the rest…

UV dye can help in detecting oil leak sources.

It can be very difficult to pinpoint and detect the cause of leaks when the engine is covered with oil. Sometimes it’s best to clean the motor to help determine where the oil is coming from. By adding UV (Ultra Violet) Dye, the leak can be traced much easier back to the source. To begin with, it’s best to determine what type fluid is leaking, there are several things that could be leaking on an automobile.

Read the rest…

Ford Expedition lean codes could caused by a leaky PCV hose.

If a car has a check engine light on and has P0171 and P0174 codes stored, the most likely cause is a vacuum leak. These codes are set by the car’s computer when it sees too much oxygen in the exhaust. Excessive oxygen readings in the exhaust will set lean codes. This does not mean that the oxygen sensors are defective. It is a common mistake for people to replace oxygen sensors when lean codes are present. Just because the code is related to oxygen sensor readings, it doesn’t mean that the oxygen sensors are bad. If both of these codes are stored this means that both banks of the engine have excessive oxygen in the exhaust. If the oxygen sensors are replaced it’s most likely that the same codes will reappear. It is very uncommon for two oxygen sensors to fail at the same time.

Read the rest…

Tree style masking stations like this one holds paper and tape for easy access.

Professional autobody paint shops prevent much overspray by masking the car well prior to painting. Taking time for preparation can save a lot of time on cleanup later. Masking machine stations hold rolls of paper and masking tape for easy application. Windows trim pieces and tires can be taped off to prevent overspray. Many do-it-yourselfers don’t realize how easy it is to get overspray on the car. When there is a chance of getting overspray on the vehicle its best to mask the car.

Read the rest…

Power window problems? Read on for free tips.

Broken power windows are usually caused by one of several things. The most common problem is a bad power window motor. The second most common problem is the regulator, followed by a bad power window switch. If the window regulator is broken it could be binding or the cable could be off one of the pulleys. In a few cases, the window may just be STUCK. This happens sometimes in rear windows that get little use. The weather stripping that the window slides in (AKA called a window run) can sometimes prevent the window from moving.

Read the rest…